How to Install a PVC Fence
There are a few important things to consider when you’re contemplating installing fencing. The first step is decide the location you’d like to put the fence. Then, you need to prepare the ground. Then, you’ll have to put the posts in place. You may also have to alter the fence’s height based on the size of your property.
Preparing the ground
Getting the ground ready for Vinyl fences the fence is a crucial step in the process. This is because the fence posts must be securely buried. If they aren’t then the fence could be blown over by the wind.
Before you start digging, you should check the local utility company to ensure there aren’t any underground utilities that could hinder the construction. You can dial 811 to get your yard marked for underground lines.
A gravel base should be prepared for the fence posts. This will allow water to drain away from the posts. It provides a solid foundation for the blocks.
Once you have the base, it’s time to put in the vinyl fences fence. The material must be at least four feet long and 1 inch thick. If you have access to an auger, then you can employ it to make the holes for the fence posts.
Before digging, take out any plants or shrubs that may block the hole. In some instances it is easier to get rid of the ground rather than digging it. Avoid digging in sandy or rocky soil if you must.
Then, you should mark the highest and lowest points in your yard. A string level is the most effective method to accomplish this. Attach the string level to stakes at least one foot above the ground. The string level will act as a reference for the fence posts.
You’ll need to drill pilot holes if your land is extremely dry. This will speed up the process.
You’ll also need to mark the holes. This can be done using spray paint or a marker. You can also employ a mason’s lines to make sure that the posts are straight.
You can also fill in the gap with decorative stones. These stones are suitable for smaller gaps. You’ll need to find a different way to fill a larger gap. You can also try placing dirt in the gap. This is a cost-effective and effective solution.
Posts are erected
It is often difficult to position the posts. The first step is to locate the ideal location. You can use a spirit level, a mark made to determine the width of the post or a measuring tool.
Then, you can place the posts that are at the corner and Vinyl fences the end. Also, set the middle and top rails. You may have to cut some sections. You could also use rails to act as a spacer between the posts.
Once you’ve located the center of each hole using a tape measure or stakes to mark the middle of the posts with a tape measure. To determine the depth, you could also use the stringline. Once you have drawn the string line then tie the ends of the string. This will ensure the fence will be straight.
After the posts are firmly set after which you can fill the bottoms with 6 inches of gravel. This will keep the posts in place and provide drainage.
Use a concrete that is quick-setting when putting fence posts into concrete. This type of concrete sets in three to four minutes. If you’re installing privacy fencing, make certain not to tighten too much the panels. The panels should be placed 22 inches above the ground. The panel should be secured with #10 x 1″ self-tapping stainless steel screws.
You can attach the posts to your colored vinyl fences fence by using two screws. If you are installing a privacy fence you should leave one screw on the top rail. Duct tape can be used to cover the bottom rails prior to putting them into the posts. This will prevent concrete from leaking into the bottom horizontalrail.
When you are happy with the placement, take off the duct tape. Then, insert the top rail into each of the posts. The pickets can be attached to the rails.
You can also set the bottom rails at the corners. You can use aluminum u-channels for fixing the rails onto the post.
Assembling the panels
The fence posts being lined up correctly is essential to the success of installing vinyl fence. There may be different methods based on the design of your fence. If you’re installing an square or oval fence, the following steps will help you get started.
Before you begin, make sure to check your deed and local zoning laws. Also, notify neighbors of your plan. You may require permission to build if you plan to install an electric fence.
Once you have all your posts in place now is the time to put in your rail brackets. These screws are fixed to the inside of the post. This allows for easier manipulation of the posts as they are inserted.
Before setting up your rail brackets, you should install the bottom rail. Pre-assembled vinyl gates with fences fences (try this website) panels usually include two rails. You may have to modify the rails to fit your terrain.
Once the bottom rail is in place, you can then install the middle rail. You can also install the top rail the same way. This step can be done by using an aluminum uchannel. It can be put into your posts with #8 x 1” screws.
You can then attach your pickets one at a. Once they’re all in place you can begin to attach your C channel brackets. To hold them in place you can put stakes at their corners. To connect stakes you can use cotton string.
Spray paint markers can be used to mark your line. This will ensure that the fence is level when you install it.
Additionally, you will have to install privacy fence panels panels. These should be installed on the back side of your fence. You can also add pea gravel to your holes to help keep them in place. You can make your slope gentler by putting your fence panels on one side so that they “step down”. If the slope is a steep one you’ll need to set up your fence so that it “steps down” from the top to the bottom.
Problems with height changes
If you’re looking to put up a PVC fence you might have difficulty when it comes to lining up the posts. There are two methods to achieve this. The first is to put the posts on the ground. The second is to place them in a line. The first method is easier and ensures that concrete is placed under and around each post. In the second method, you will have to remove the posts and then fill them with dirt.
Make sure you have enough backfill in place to hold the posts while digging them out. To place the posts in the base of the gravel it is necessary to dig about 6 inches. You may also employ a hole digger to make holes. The tension bar can be attached to the mesh in the last step. Then staple the upper end of the mesh to the fence.
If you have difficulty aligning the posts, you can take any rails that are too high. While this isn’t easy however, it is possible to accomplish it with two people. If you have a hammer and chisel, you can use them to tack the threads of the bolts. This will stop them from escaping the fence when you take it out.